Canoga-perkins 9161 Network Interface Device Manual do Utilizador Página 1

9161 Network Interface Device User Manual

9161 Network Interface Device 1-2

Chapter 2 Set-up and Installation This section describes how to set up and install the 9161. Before setting up the 9161, make sure the serial cable (r

Cabling for the 9161 includes the serial cable to the Terminal port, the Ethernet cable for a UTP port, and the fiber optic link to the Tx and Rx port

Chapter 3 User Operation This chapter describes the hardware features and functions of the 9161. 3.1 9161 Functions and Power-Up During the initial p

Table 2. 9161 Interface LEDs LED Status Description TX Off No transmission activity Green blinking Transmission activity Amber System self-te

3.3.2 Link Loss Forwarding When LLF is enabled, a fault on one side of the 9161 propagates to the other side to notify that device and stops signal t

9161 Network Interface Device 3-4

Chapter 4 Management - VT-100 You can manage the system through VT100 Terminal Emulation, which is accessible by a Telnet session, HyperTerminal or si

4.3 Management User Interface The Management User Interface for the 9161 provides screens for setup, monitoring, and diagnostics. You can access the

4.3.2 User Interface Organization The user interface consists of selectable, nested screens, available in this order: Main Menu 1) System 1) S

4.4 9161 Main Menu The first screen is the Login Menu. If this is your initial setup and no password has been set, press <Enter> at the prompt

Selection Description 5) Security Configuration Shows parameters for passwords, lockout, and logout; you can set options 6) Account Configuration Sh

IP SETTINGS Local MAC Address : 00 00 00 06 01 00 1. Local IP Address : 172.16.3.34 2. Subnet Mask

3. To return to the IP Settings screen, press <Esc>. Use the Dynamic ARP Table to view the currently assigned IP and MAC addresses for various

4.5.4 Notification Destination Table Screen The Notification Destination Table screen lists information about and options to set up hosts to receive n

SECURITY CONFIGURATION PASSWORD CONFIGURATION 1. Minimum Length : 0 2. Minimum Alpha Characters

Menu Item Description 15. Lockout Console Port Enable or disable access to the serial port 16. Inactivity Logout time Set the time, between 1 and 3

Table 6. Switch Configuration Menu Options Menu Item Description 1. Global Spanning Tree Parameters Set the network-wide parameters 2. Multiple Spa

GLOBAL SPANNING TREE PARAMETERS 1. Admin Mode : disabled 2. Version : 802.1s 3. Configuration Name : 00

3. To return to the Switch Configuration menu, press <Esc>. MST INSTANCE CONFIGURATION CONFIGURED MULTIPLE SPANNING TR

CAUTION! This product may contain a laser diode operating at a wavelength of 1300nm - 1600nm. Use of optical instruments (e.g., collimating optics) w

10G 1 STATISTICS Port Mode : Disabled Port Up Time : 0 day 0 hour 26 min STP BPDUs Txed : 0 STP BPDUs Rxed : 0 RST BPDUs Txed : 0 R

4.6.5 VLAN Configuration Use the VLAN Configuration screen to view and set VLAN parameters for the 9161. See Figure 23. To access the VLAN Configura

GVRP INFORMATION PORT/LAG MODE JOIN TIMER LEAVE TIMER LEAVEALL TIMER SP 1 Disable 20 60

10G 1 INFORMATION Model Number : 9500-330 Model Description : 10/100/1000 UTP Interface Serial Number : 200311

REPORTS 1. Description 2. Traps Log 3. Fdb Log 4. Main Menu Figure 29. Reports Menu Table 9. Reports Menu Option Definitions Parameter Descri

FDB LOG Count VlanId MAC Port Status 156 00 01 00 D0 B7 83 45 CB 1

LATENCY/JITTER TEST Test IP Address 172.16.150.1 Test Duration 07:00 Round Trip Packets 720 Drop

4.10 Utilities Use the Utilities screen to set the time and date, restore defaults, reset the system, or start using new firmware. See Figure 36 and

9161 Network Interface Device 4-22

Chapter 5 Maintenance and Troubleshooting 5.1 General Maintenance Well-maintained components and clearly identified cables help assure optimum system

NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation, operati

5.3.1 Measure Transmitter Output Power To measure the output power, follow these steps: 1. Clean the connectors on the fiber optic test cable, then p

5.3.3 Measure Fiber Link Attenuation Determine and record link attenuation before starting normal link traffic. The attenuation factor identifies po

5.4.2 New Installation On new installations, make sure that all steps in Chapter 2 are complete, then follow these steps: 1. Check that the STA LED i

Chapter 6 Specifications See also the specifications for the chassis or standalone enclosure. 6.1 9161 Specifications Standards: IEEE 802.3 Dimensions

9161 Network Interface Device 6-2

Appendix A Warranty Limited Lifetime Warranty Effective for Products Shipped February 1, 2003 and After, Canoga Perkins warrants that, at the time of

Limitations Canoga Perkins may at its sole discretion modify its Limited Warranty at any time and from time to time. Other than those expressly stated

Appendix B Acronym and Abbreviation List FPGA Field Programmable Gate Array GARP General Attributes Registration Protocol for registering a client s

CANOGA PERKINS CORPORATION 20600 Prairie Street Chatsworth, California 91311-6008 USA Phone: (818) 718-6300 FAX: (818) 718-6312 Web Site: w

Table of Contents Chapter 1 Overview...1-1 Chapter 2 S

Chapter 5 Maintenance and Troubleshooting...5-1 5.1 General Maintenance ...

List of Figures Figure 1. The 9161 Front Panel...

List of Tables Table 1. 9161 Management LEDs ....... 3-

Chapter 1 Overview The 9161 is a 2-Port 10 Gbps Network Interface Device that provides intelligent optical demarcation and terminates managed transpor